
全部分类

T082D
● 多量程、多分度、多采样频率
● 标准ModBUS-RTU通讯
● 防护等级IP66
● 一进一出数字变送器
● 宽电源供电: 7~ 25VDC
● Use the multi-turn potentiometer with high stability to do compensation and adjustment
● Cover with waterproof rubber gasket which could be waterproof and dustproof, suitable for harsh industrial conditions
● Multiple Linearity adjustment points with different capacity, different division and sampling rate
● IP66 protection digital transducer
● Powersupply:7 ~ 25VDC
特点
● 多点线性校准● 多量程、多分度、多采样频率
● 标准ModBUS-RTU通讯
● 防护等级IP66
● 一进一出数字变送器
● 宽电源供电: 7~ 25VDC
Features
● Using special waterproof connector● Use the multi-turn potentiometer with high stability to do compensation and adjustment
● Cover with waterproof rubber gasket which could be waterproof and dustproof, suitable for harsh industrial conditions
● Multiple Linearity adjustment points with different capacity, different division and sampling rate
● IP66 protection digital transducer
● Powersupply:7 ~ 25VDC

T098BH
● 电源与信号隔离,抗干扰能力强
● 高精度,经筛选的精密运放、精密电阻
● 多级有源滤波处理,输出信号稳定准确
● 适应多种灵敏度传感器,零点可调范围宽
● The power is isolated from signal, strong anti-interference ability.
● High accuracy, high precision amplifying and resistance
● Stable and accurate output with multi-grades active filter.
● Could be connected with multi-capacity load cells with wide scope of zero point adjustment
特点
● 集合多种输出信号土10V,4 ~ 20mA,0~ 20mA● 电源与信号隔离,抗干扰能力强
● 高精度,经筛选的精密运放、精密电阻
● 多级有源滤波处理,输出信号稳定准确
● 适应多种灵敏度传感器,零点可调范围宽
Features
● Multi-output +10V,4~ 20mA,0~ 20mA● The power is isolated from signal, strong anti-interference ability.
● High accuracy, high precision amplifying and resistance
● Stable and accurate output with multi-grades active filter.
● Could be connected with multi-capacity load cells with wide scope of zero point adjustment

T097
● 补偿调节采用高稳定性的多圈电位器
● 盖板有防水橡胶垫圈,防水,防尘,适用于环境条件恶劣的工业现场
● 防止感应雷和浪涌信号对传感器的损坏
● 四进一出接线盒
● Use the multi-turn potentiometer with high stability to do compensation and adjustment
● Cover with waterproof rubber gasket which could be waterproof and dustproof,suitable for harsh industrial conditions
● Prevent sensor damage from lightning induction and surge signal
● Use one input and one output junction box
特点
● 采用专用防水接头● 补偿调节采用高稳定性的多圈电位器
● 盖板有防水橡胶垫圈,防水,防尘,适用于环境条件恶劣的工业现场
● 防止感应雷和浪涌信号对传感器的损坏
● 四进一出接线盒
Features
● Using special waterproof connector● Use the multi-turn potentiometer with high stability to do compensation and adjustment
● Cover with waterproof rubber gasket which could be waterproof and dustproof,suitable for harsh industrial conditions
● Prevent sensor damage from lightning induction and surge signal
● Use one input and one output junction box

T093
● 模拟输出信号可选择0-20mA、4-20mA. 0-10V、1-5V,数字通讯接口可选择RS485或RS232
● 双排6位LED数码管分别显示实时测量值、峰值、输出电流值、1I/O状态信息
● 控制器带有上限、中限、下限界限判断功能
● I/O有4入6出,可自定义输入输出端口功能
● 可通过上位机进行驱动控制器输出,可部分替代PLC
● 控制器供电电源采用DC24V供电,压宽士5V,更加安全稳定
● 开孔式面板安装,面板面积仅110mm (宽) x62mm (高)
● Analog output signal could be 020mA, 4-20mA 0-10V, 1-5V, digital communication interface as RS485 or RS232
● Dual 6-digit LED digital tube shows real-time measurement, peak, output current value,1/ 0 status information
● Controller with the upper, middle and lower limits judgment
● 1/O4 input and 6 output, you can customize the input and output port function
● Can be driven by the host computer controller output, can replace part of the alternative PLC
● DC24V power supply, voltage土5V, more secure and stable
● Dimension of panel is only 110mm (width) x 92mm (high)
特点
● 用于需要将测力信号转换为数字通讯信号、标准模拟输出信号及简单控制的场合● 模拟输出信号可选择0-20mA、4-20mA. 0-10V、1-5V,数字通讯接口可选择RS485或RS232
● 双排6位LED数码管分别显示实时测量值、峰值、输出电流值、1I/O状态信息
● 控制器带有上限、中限、下限界限判断功能
● I/O有4入6出,可自定义输入输出端口功能
● 可通过上位机进行驱动控制器输出,可部分替代PLC
● 控制器供电电源采用DC24V供电,压宽士5V,更加安全稳定
● 开孔式面板安装,面板面积仅110mm (宽) x62mm (高)
Features
● Use for turning the analog force signal to digital output, the standard analog output signal and simple control of the occasion● Analog output signal could be 020mA, 4-20mA 0-10V, 1-5V, digital communication interface as RS485 or RS232
● Dual 6-digit LED digital tube shows real-time measurement, peak, output current value,1/ 0 status information
● Controller with the upper, middle and lower limits judgment
● 1/O4 input and 6 output, you can customize the input and output port function
● Can be driven by the host computer controller output, can replace part of the alternative PLC
● DC24V power supply, voltage土5V, more secure and stable
● Dimension of panel is only 110mm (width) x 92mm (high)

T088
● 支持1到4路台秤接入,AD最大速率200次/秒
● 100000高显示精度,6000e CMC认证精度
● 1路RS232/485串口,2路以太网口( 100M),自带交换机功能
● 支持MODBUS-RTU & MODBUS -TCP
● 支持PROFINET, TCP/IP
● 支持手机APP或计算机工具配置仪表和标定
● 标准工业导轨安装(DIN )
● 1 to 4 scales input, 200HZ ADC speed
● 100000display division, 6000e CMC approval
● One Serial port: RS232/485, 2LAN port
● MODBUS-RTU & MODUBS-TCP
● PROFINET for Siemens, TCP Report weight
● Mobile APP Configure and Calibration
● PC tool Configure and Calibration
● Standard industrial rail mounting (DIN)
特点
● 主要应用于PLC控制系统或DCS.计算机管理控制系统,仪表将重量通过串口或以太网口或PROFINET工业以太网将重量传输给PLC或DCS、计算机;● 支持1到4路台秤接入,AD最大速率200次/秒
● 100000高显示精度,6000e CMC认证精度
● 1路RS232/485串口,2路以太网口( 100M),自带交换机功能
● 支持MODBUS-RTU & MODBUS -TCP
● 支持PROFINET, TCP/IP
● 支持手机APP或计算机工具配置仪表和标定
● 标准工业导轨安装(DIN )
Features
● This indicator is an industry weighing controller, high accuracy, support 1 to 4scales input, and support PROFINET and MODBUS-TCP communication, typical for weighing,batching, flling system work together with PLC or DCS● 1 to 4 scales input, 200HZ ADC speed
● 100000display division, 6000e CMC approval
● One Serial port: RS232/485, 2LAN port
● MODBUS-RTU & MODUBS-TCP
● PROFINET for Siemens, TCP Report weight
● Mobile APP Configure and Calibration
● PC tool Configure and Calibration
● Standard industrial rail mounting (DIN)

T092 手持式仪表
USB数据接口,支持热插拔; 显示峰值力、实时值,TX图显示测力计还可显示测试线,可监控和追朔测试全过程。
● 显示峰值力、实时值,TX图显示测力计还可显示测试线,可监控和追朔测试全过程;
● 上下限偏差值自由设定、限内限外报警任意选择;
● 上下限两点电平输出、蜂鸣器、显示屏同时提示报警;
● 屏幕显示方向可180°翻转;
● 三种单位N、 kg 、 Ib自动换算;
● 具有峰值保持功能、峰值自动解除及解除时间自由设定;
● 通过PC配套专用的测试软件,可无限存储、传递、追朔测试曲线数据;
● 可在软件界面中打印测试结果;
● 可配置各类测试机台、实现各种测试
● USB connect interface, support hot-swappable
● Show peak force, real-time value, TX diagram display test line, can monitor and trace the whole process of testing;
● Upper and lower limits can be set freely, alarm of limits could be chosen
● Upper and lower limit two-point output, buzzer, display also prompts the alarm
● Irection buttons and display can be rotated 180°
● Enable automatic unit conversion: N, kg, and Ib; pressure unit Mpa can be converted as well
● Peaks can be held or cleared; clearing time can be set
● Through the PC supporting the dedicated test software, can be unlimited storage, transmission, tracing test curve data
● Print test results can be printed in the software interface
● Can configure a variety of test machines, to achieve a variety of tests applications
特点
● USB数据接口,支持热插拔;● 显示峰值力、实时值,TX图显示测力计还可显示测试线,可监控和追朔测试全过程;
● 上下限偏差值自由设定、限内限外报警任意选择;
● 上下限两点电平输出、蜂鸣器、显示屏同时提示报警;
● 屏幕显示方向可180°翻转;
● 三种单位N、 kg 、 Ib自动换算;
● 具有峰值保持功能、峰值自动解除及解除时间自由设定;
● 通过PC配套专用的测试软件,可无限存储、传递、追朔测试曲线数据;
● 可在软件界面中打印测试结果;
● 可配置各类测试机台、实现各种测试
● USB connect interface, support hot-swappable
● Show peak force, real-time value, TX diagram display test line, can monitor and trace the whole process of testing;
● Upper and lower limits can be set freely, alarm of limits could be chosen
● Upper and lower limit two-point output, buzzer, display also prompts the alarm
● Irection buttons and display can be rotated 180°
● Enable automatic unit conversion: N, kg, and Ib; pressure unit Mpa can be converted as well
● Peaks can be held or cleared; clearing time can be set
● Through the PC supporting the dedicated test software, can be unlimited storage, transmission, tracing test curve data
● Print test results can be printed in the software interface
● Can configure a variety of test machines, to achieve a variety of tests applications
上一页
1
下一页